# Basic Technology Examination Questions For JSS1 | 1st, 2nd And 3rd Term

Basic Technology Examination Questions For JSS1 | 1st, 2nd And 3rd Term

SUBJECT: BASIC TECHNOLOGY TIME:
CLASS: JSS 1

A shaper drawn one a plane is called —- (a) two dimensional shape (b) 3-D shape (c)4-D shape | webemtech
What is a plane? (a) a rough surface (b) a flat surface (c) a slanted surface (d)a smooth surface
A plane figure with 3 sides and 3 angles is called — (a)hexagon (b)sea line triangle (c)isosceles triangle (d)triangle
A —- has a set of permits equidistant from a fined point (a) triangle (b)rectangle (c)square (d)circle
Which of the following is not a type of plane shape (a)quadrilateral (b)triangle (c)pentagon (d)cuboid
The types of polygon are (a)regular and heptagon (b) irregular and decagon (c)regular and octagon (d)regular and irregular
The inside calipers are used to measure the — of a hole (a)inside diameter (b)outside diameter (c)length (d)depth
Which of the following is not a measuring tool (a)the metre rule (b)add legs calipers (c)dividers (d)compasses
Examples of driving tools are as follows except (a)screw driver (b)ball-pin hammer (c)mallet (d) chisel

Basic Technology Examination Questions For JSS1 | 1st, 2nd And 3rd Term

The planning of wood to a smooth and pin finish is done with which of the following tools (a)try square (b)saw (c)plane (d) mitre square
—– is used to mark off length by the action of its nail or pin (a)marking gauge (b)G-clamp (c)sliding bevel (d)bradawl
Holding tool device are — and —- used to hold work pieces on the bench (a)G-clamp and F- clamp (b)Bench and hook (c)provision and tools (d)G-Clamp and provision
The metal worker pencil is called —- (a)the scriber (b)the divider (c)surface plate (d)the punch
A precision measuring tools used for determining the depth of holes is called —- (a)micrometer (b)square head (c)centre square (d)depth gauge
Which of the following is not a type of screw driver (a)flat (b)star (c)rechet (d)out set

What is the name of the above tool (a)chisel (b)screw driver (c)file (d)scriber
The part labeled b is called what (a)gang (b)safe edge (c)cutting fall (d)blade
— is define as the ability of the student to use drawing instruments and materials to produce good drawing (a)surface practice (b)bowel practice (c)drawing practice (d)border drawing
Two set of instruments normally used in drawing border, vertical and horizontal lines are (a)tee-square and set square (b)tee-square and protractor (c)sets-square and ruler (d)tee-square and ruler
—– is the ability to do work (a)power (b)energy (c)work (d)force
Which of the following is not a form of energy (a)electrical (b)chemical (c)sock (d)cyclotron
—- is the rate at which work is done (a)energy (b)force (c)work (d)power
The energy of a body at rest is called what? (a)potential energy (b)kinetic energy (c)mechanical energy (d)static energy
—- is a form of energy which leads to the rise in temperature of a body (a) heat (b)electrical (c)kinetic (d)chemical
Nuclear energy comes from the splitting of —- (a)atom (b)molecule (c)electron (d)proton
A boy pushes a load of mass 10kg to a distance of 20 metres in 10 seconds. What is the work done by the boy? (a)200N (b)300N (c)200N (d)400N

Basic Technology Examination Questions For JSS1 | 1st, 2nd And 3rd Term

Use the diagram below to answer question 27, 28 and 29
What does the diagram represents (a)molecule (b)atom (c)electron (d)neutron
The part labeled t is called (a) electron (b)neutron (c)proton (d)molecule
L in the diagram represent the —- (a)circle (b)middle (c)nucleus (d)core

The try square is used for testing the —- of a surface (a)flatness (b)smoothness (c)squareness (d)roughness

## Basic Technology Examination Questions For JSS1 | 1st, 2nd And 3rd Term SECTION B

Answer any three questions from this section
1). What do you understand by power tools?
b). Mention three wood work medium
2). State three (3) types of boning tools
b). List three (3) types of holding tools devices
3). Write short note on the following
i). scriber
ii). Try Square
iii). Centre square
4). Mention 2 instrument used in board practice
b). Define energy
5). Mention 5 forms of energy
6). Define power
b). Calculate the work done when a force of 20N moves a body through a distance of 60m

Message Us on WhatsApp 